Product Overview
DAYTONA THROTTLE SLEEVE, UNIVERSAL 25.4MM, HONDA, 42577
The Daytona Universal 25.4mm (1"), Honda 25.4mm / Yamaha 25.4mm type throttle sleeve is made without ribs for easy grip replacement. Since there is no need to shave the ribs, it is a convenient option when replacing with custom grips or heated grips on your Honda CMX500, Honda Rebel 250/500, Yamaha Dragstar (Vstar in Aust.) DS400, DS650 & DS1100 etc. The genuine (OEM) sleeves have variations in white, grey, and black depending on the bike model. However, this throttle sleeve is black in colour to be less noticeable when customising.
An essential part for anyone looking to replace handlebars or customise with aftermarket grips or repair their bike after a fall. Whether you're a seasoned builder, a newcomer to the custom scene, or simply need a new OEM replacement, the Daytona flat type of throttle tube is a worthy addition to avoid frustrating grip swap issues….
RECOMMENDED GRIP LENGTH:
-> 128mm open end
-> 2mm to 4mm longer for closed end
-> Can be trimmed shorter if needed.
MODEL REFRENCE:
-> REBEL250 / ABS ('17 to '23) * NOTE: Genuine sleeve is a closed end sleeve.
-> HONDA REBEL250 S EDITION ('20 ~ '23), -> HONDA REBEL / CMX500 ('17 ~ '23)
-> HONDA STEED 600/400VLX/ VSE/VCL/VLS, -> HONDA SHADOW 750/400 (to '06)
-> HONDA SHADOW 750/400 (to '06), -> HONDA SHADOW SLASHER 750/400 (to '06)
-> YAMAHA DRAGSTAR/VSTAR DS400 (to '12) / DSC400 (to '12), YAMAHA DS650 (to '12) / DSC650 (to '12)
-> YAMAHA DRAGSTAR *DS1100 (to '08) / DSC1100 (to '08)
-> KAWASAKI VULCAN 400 / II / Classic (to '04), -> KAWASAKI VULCAN 800 / Classic (〜'04)
NOTES:
+ Since it is a general-purpose product, there are some bike models that cannot be installed due to differences in cable winding angle and hole size. Always check the image above before purchase.
+ Use your factory workshop manual to fit to your bike.
+ The dimensions shown are design dimensions. They may be slightly different depending on the manufacturing process.
+ Cutting or trimming may be required depending on the bike model and grip type used.
+ This is a general-purpose product. Please measure the factory throttle sleeve in use and select a throttle wire take-up diameter and length close to that of the factory OEM sleeve.
+ Clearance and throttle position may differ from the stock in some models.
+ The outer diameter of the grip mounting area is about 0.2mm smaller than that of the genuine parts of each manufacturer. Therefore, depending on the bike model, the genuine grips may not be usable.
+ We recommend applying a small amount of grease to the outer circumference of the handlebar to eliminate contact noise with the handlebar when idling or to improve throttle operation.
+ There is no grip rotation stop. When installing, please use a suitable grip bond / glue (sold separately) or “safety wire” the grips to securely fasten.
+ The diameter of the windings may be different from the stock windings for the referenced compatible bike models. However, there is generally no problem in use.
ATTENTION:
1. Heated Grips wiring may need to face a certain position for wiring. Always check prior to fitment.
2. Always check the position of the heated grip wiring before riding to ensure fitment is correct and wiring is not obstructed.
3. We will not be responsible for issues or accidents caused by a bad glue adhesion, wiring defects, or re-checking the position of the grip.
4. Always use quality grip glue suitable for the type of grips you are fitting. Heated grips may require special glue. Some grips may require low solvent glue (check grips selected).
Daytona Japan (Daytona Corporation) has been a leader in motorcycle parts industry since 1972. Daytona provides original and customized motorcycle parts and accessories throughout Japan and to the international marketplace. Daytona’s specialty is R&D to develop original motorcycle parts and accessories which meet the demand in the highly competitive Japanese motorcycle industry and abroad.
